Altium Schematics and Footprints Guidelines - Revision history

Samchen2: Added more info from PCB design feedback for Phoenix

2024-04-01T03:41:15Z

Added more info from PCB design feedback for Phoenix

← Older revision		Revision as of 03:41, 1 April 2024
Line 20:		Line 20:
	* Surface-mount pads: pads that only exist on the surface of a layer. They do not cut through the board. Used for surface-mount devices/technology (SMD/SMT). Usually harder for soldering but required for most chips and smaller electrical components.		* Surface-mount pads: pads that only exist on the surface of a layer. They do not cut through the board. Used for surface-mount devices/technology (SMD/SMT). Usually harder for soldering but required for most chips and smaller electrical components.
	* Through-hole pads: pads that cut through the board. Used for through-hole technology (THT). Usually easier for soldering.		* Through-hole pads: pads that cut through the board. Used for through-hole technology (THT). Usually easier for soldering.

			=== '''Symbols and Footprints''' ===

			* <span class="s1"></span>When picking/editing symbols, make sure the pad numbers in the symbol match the pad numbers in the corresponding footprints.
			* <span class="s1"></span>It is best if a symbol corresponding to a footprint can resemble the footprint as closely as possible. This can provide more clarity when trying to assemble the board.

	=== Altium Schematics (SchDoc) ===		=== Altium Schematics (SchDoc) ===
Line 25:		Line 30:
	* Designing the schematics means you will wire up the necessary electrical components that make your PCB board function electrically. You should refer to the datasheets of different parts to see the additional components you might need.		* Designing the schematics means you will wire up the necessary electrical components that make your PCB board function electrically. You should refer to the datasheets of different parts to see the additional components you might need.
	* The Altium schematic sheet of a completed board shows a block diagram with all the electrical components of the board. Each block represents a chip and has a detailed sheet associated with it.		* The Altium schematic sheet of a completed board shows a block diagram with all the electrical components of the board. Each block represents a chip and has a detailed sheet associated with it.
			** In KiCAD, this organization can be done by separating the schematics sheet into sections separated by lines or rectangle borders. Labeling different sections can also help with clarity.
	* If you are confused about the functions of components shown in a schematic file, [https://www.khanacademy.org/science/electrical-engineering Khan Academy] can be a great resource for understanding electrical components and what they are used for.		* If you are confused about the functions of components shown in a schematic file, [https://www.khanacademy.org/science/electrical-engineering Khan Academy] can be a great resource for understanding electrical components and what they are used for.
	* When the schematic is done, Altium will generate a netlist and import it to the PCB document. You will see all the nets turned into tracks on the PCB, which size can be customized.		* When the schematic is done, Altium will generate a netlist and import it to the PCB document. You will see all the nets turned into tracks on the PCB, which size can be customized.
Line 30:		Line 36:
	** To find where the schematic of a missing part is, use the Find tool (Ctrl + F) and type in the part name.		** To find where the schematic of a missing part is, use the Find tool (Ctrl + F) and type in the part name.

	=== Altium ~~Footprints &~~ PCB (PcbDoc) ===		=== Altium PCB (PcbDoc) ===
	This is when we switch from designing the circuit to laying out the PCB itself, i.e. planning out the physical locations of each part and component.		This is when we switch from designing the circuit to laying out the PCB itself, i.e. planning out the physical locations of each part and component.

	==== Layers in Altium ====		==== Layers in Altium ====

	* The PCB can have many copper layers that supply power to different components running on different voltages.		* The PCB can have many copper layers that supply power to different components running on different voltages. They are called power layers/planes.
			** In KiCAD, to create a power layer supplied by a surface-mount pad, you need to connect the pad to a via If the layer is supplied with a through-hole pad, there's no need for a separate via.
			** Note that traces cutting through the power layer can slow down the movement of electrical charges because a longer path might be needed to travel from one pad to another. Thus, even with a power layer, it is best to leave an open, straight-line path between the pad supplying power and the pad receiving power.
	* The transparent function in Altium will show two sides of every layer at the same time, which can be confusing at first and will take time to get used to.		* The transparent function in Altium will show two sides of every layer at the same time, which can be confusing at first and will take time to get used to.
	* By default, all components on the same page in the schematic document will be in the same “room,” and you can move all the components together in that room.		* By default, all components on the same page in the schematic document will be in the same “room,” and you can move all the components together in that room.
Line 50:		Line 58:
	* A mechanical hole for mounting certain big components (like battery holders) cannot interfere with any vias or traces, or else an electrical connection cannot be made.		* A mechanical hole for mounting certain big components (like battery holders) cannot interfere with any vias or traces, or else an electrical connection cannot be made.
	* Select the layer you’re working on with tabs at the bottom of the window for easier selection of traces/components.		* Select the layer you’re working on with tabs at the bottom of the window for easier selection of traces/components.
			* Blind vias (vias that do not cut through the entire board) can increase the cost of manufacturing and are sometimes less reliable (more prone to cracking). It is advised to use through vias (vias that cuts through the entire board) whenever possible.

	After all the checks are done, a 3D model will be generated, and all the information can be sent to a fabrication company.		After all the checks are done, a 3D model will be generated, and all the information can be sent to a fabrication company.

	=== Authors' Note ===		=== Authors' Note ===
	This page is written on January 18, 2024 by [https://ssi-teams.slack.com/team/U045V0EE46Q Sam Chen] and [https://ssi-teams.slack.com/team/U04484CR1SQ Abelle Jayadinata] based on the materials covered in the [https://docs.google.com/document/d/14Ilml3RbP6zr4GWvh4mAetntX6BX1ORxpdkTMpOlbTM/edit?usp=sharing Winter 2024 Altium PCB Workshops] hosted by [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt]. We thank [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt] and [https://ssi-teams.slack.com/team/U0602L5Q31B Ethan Brinser] for their expertise and knowledge, which made the writing of this page possible.		This page is written on January 18, 2024 by [https://ssi-teams.slack.com/team/U045V0EE46Q Sam Chen] and [https://ssi-teams.slack.com/team/U04484CR1SQ Abelle Jayadinata] based on the materials covered in the [https://docs.google.com/document/d/14Ilml3RbP6zr4GWvh4mAetntX6BX1ORxpdkTMpOlbTM/edit?usp=sharing Winter 2024 Altium PCB Workshops] hosted by [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt]. It is updated on March 31, 2024 to include more detailed information from PCB design feedback. We thank [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt] and [https://ssi-teams.slack.com/team/U0602L5Q31B Ethan Brinser] for their expertise and knowledge, which made the writing of this page possible.

	<nowiki>[[:Category:Altium]]</nowiki>		<nowiki>[[:Category:Altium]]</nowiki>

Samchen2: Added pad descriptions

2024-04-01T03:37:41Z

Added pad descriptions

← Older revision		Revision as of 03:37, 1 April 2024
Line 17:		Line 17:
	* Trace: the copper wires that connect different electrical components on the PCB.		* Trace: the copper wires that connect different electrical components on the PCB.
	* Via: A hole in the PCB that electrically connects through the board. The copper conductive part is inside the PCB. This moves the copper track to another layer in the PCB and prevent two nets from overlapping on the same layer.		* Via: A hole in the PCB that electrically connects through the board. The copper conductive part is inside the PCB. This moves the copper track to another layer in the PCB and prevent two nets from overlapping on the same layer.
			* Pads: metal regions needed to electrically connect components on the board with the inner traces and wirings.
			* Surface-mount pads: pads that only exist on the surface of a layer. They do not cut through the board. Used for surface-mount devices/technology (SMD/SMT). Usually harder for soldering but required for most chips and smaller electrical components.
			* Through-hole pads: pads that cut through the board. Used for through-hole technology (THT). Usually easier for soldering.

	=== Altium Schematics (SchDoc) ===		=== Altium Schematics (SchDoc) ===

Samchen2 at 07:16, 19 January 2024

2024-01-19T07:16:45Z

← Older revision		Revision as of 07:16, 19 January 2024
Line 53:		Line 53:
	This page is written on January 18, 2024 by [https://ssi-teams.slack.com/team/U045V0EE46Q Sam Chen] and [https://ssi-teams.slack.com/team/U04484CR1SQ Abelle Jayadinata] based on the materials covered in the [https://docs.google.com/document/d/14Ilml3RbP6zr4GWvh4mAetntX6BX1ORxpdkTMpOlbTM/edit?usp=sharing Winter 2024 Altium PCB Workshops] hosted by [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt]. We thank [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt] and [https://ssi-teams.slack.com/team/U0602L5Q31B Ethan Brinser] for their expertise and knowledge, which made the writing of this page possible.		This page is written on January 18, 2024 by [https://ssi-teams.slack.com/team/U045V0EE46Q Sam Chen] and [https://ssi-teams.slack.com/team/U04484CR1SQ Abelle Jayadinata] based on the materials covered in the [https://docs.google.com/document/d/14Ilml3RbP6zr4GWvh4mAetntX6BX1ORxpdkTMpOlbTM/edit?usp=sharing Winter 2024 Altium PCB Workshops] hosted by [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt]. We thank [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt] and [https://ssi-teams.slack.com/team/U0602L5Q31B Ethan Brinser] for their expertise and knowledge, which made the writing of this page possible.

	<nowiki>[[:Category: Altium]]</nowiki>		<nowiki>[[:Category:Altium]]</nowiki>

Samchen2 at 07:16, 19 January 2024

2024-01-19T07:16:00Z

← Older revision		Revision as of 07:16, 19 January 2024
Line 53:		Line 53:
	This page is written on January 18, 2024 by [https://ssi-teams.slack.com/team/U045V0EE46Q Sam Chen] and [https://ssi-teams.slack.com/team/U04484CR1SQ Abelle Jayadinata] based on the materials covered in the [https://docs.google.com/document/d/14Ilml3RbP6zr4GWvh4mAetntX6BX1ORxpdkTMpOlbTM/edit?usp=sharing Winter 2024 Altium PCB Workshops] hosted by [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt]. We thank [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt] and [https://ssi-teams.slack.com/team/U0602L5Q31B Ethan Brinser] for their expertise and knowledge, which made the writing of this page possible.		This page is written on January 18, 2024 by [https://ssi-teams.slack.com/team/U045V0EE46Q Sam Chen] and [https://ssi-teams.slack.com/team/U04484CR1SQ Abelle Jayadinata] based on the materials covered in the [https://docs.google.com/document/d/14Ilml3RbP6zr4GWvh4mAetntX6BX1ORxpdkTMpOlbTM/edit?usp=sharing Winter 2024 Altium PCB Workshops] hosted by [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt]. We thank [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt] and [https://ssi-teams.slack.com/team/U0602L5Q31B Ethan Brinser] for their expertise and knowledge, which made the writing of this page possible.

	<nowiki>[[Category: Altium]]</nowiki>		<nowiki>[[:Category: Altium]]</nowiki>

Samchen2 at 07:15, 19 January 2024

2024-01-19T07:15:24Z

← Older revision		Revision as of 07:15, 19 January 2024
Line 53:		Line 53:
	This page is written on January 18, 2024 by [https://ssi-teams.slack.com/team/U045V0EE46Q Sam Chen] and [https://ssi-teams.slack.com/team/U04484CR1SQ Abelle Jayadinata] based on the materials covered in the [https://docs.google.com/document/d/14Ilml3RbP6zr4GWvh4mAetntX6BX1ORxpdkTMpOlbTM/edit?usp=sharing Winter 2024 Altium PCB Workshops] hosted by [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt]. We thank [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt] and [https://ssi-teams.slack.com/team/U0602L5Q31B Ethan Brinser] for their expertise and knowledge, which made the writing of this page possible.		This page is written on January 18, 2024 by [https://ssi-teams.slack.com/team/U045V0EE46Q Sam Chen] and [https://ssi-teams.slack.com/team/U04484CR1SQ Abelle Jayadinata] based on the materials covered in the [https://docs.google.com/document/d/14Ilml3RbP6zr4GWvh4mAetntX6BX1ORxpdkTMpOlbTM/edit?usp=sharing Winter 2024 Altium PCB Workshops] hosted by [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt]. We thank [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt] and [https://ssi-teams.slack.com/team/U0602L5Q31B Ethan Brinser] for their expertise and knowledge, which made the writing of this page possible.

	<nowiki>[[Category:Altium]]</nowiki>		<nowiki>[[Category: Altium]]</nowiki>

Samchen2 at 07:14, 19 January 2024

2024-01-19T07:14:36Z

← Older revision		Revision as of 07:14, 19 January 2024
Line 52:		Line 52:
	=== Authors' Note ===		=== Authors' Note ===
	This page is written on January 18, 2024 by [https://ssi-teams.slack.com/team/U045V0EE46Q Sam Chen] and [https://ssi-teams.slack.com/team/U04484CR1SQ Abelle Jayadinata] based on the materials covered in the [https://docs.google.com/document/d/14Ilml3RbP6zr4GWvh4mAetntX6BX1ORxpdkTMpOlbTM/edit?usp=sharing Winter 2024 Altium PCB Workshops] hosted by [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt]. We thank [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt] and [https://ssi-teams.slack.com/team/U0602L5Q31B Ethan Brinser] for their expertise and knowledge, which made the writing of this page possible.		This page is written on January 18, 2024 by [https://ssi-teams.slack.com/team/U045V0EE46Q Sam Chen] and [https://ssi-teams.slack.com/team/U04484CR1SQ Abelle Jayadinata] based on the materials covered in the [https://docs.google.com/document/d/14Ilml3RbP6zr4GWvh4mAetntX6BX1ORxpdkTMpOlbTM/edit?usp=sharing Winter 2024 Altium PCB Workshops] hosted by [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt]. We thank [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt] and [https://ssi-teams.slack.com/team/U0602L5Q31B Ethan Brinser] for their expertise and knowledge, which made the writing of this page possible.

			<nowiki>[[Category:Altium]]</nowiki>

Samchen2 at 07:12, 19 January 2024

2024-01-19T07:12:47Z

← Older revision		Revision as of 07:12, 19 January 2024
Line 1:		Line 1:
	If you're looking at this right now, you have probably finished the design process of your PCB and picked out all the parts/components you need. If yes, it is highly recommended to make sure you also have schematics and footprints associated with every part before moving on with reading. If not, you should refer to [[The Art of PCB Design]] page before coming back.		([[:Category:Altium\|Category: Altium]]) If you're looking at this right now, you have probably finished the design process of your PCB and picked out all the parts/components you need. If yes, it is highly recommended to make sure you also have schematics and footprints associated with every part before moving on with reading. If not, you should refer to [[The Art of PCB Design]] page before coming back.

	=== PCB Terminology ===		=== PCB Terminology ===

Samchen2 at 07:08, 19 January 2024

2024-01-19T07:08:08Z

← Older revision		Revision as of 07:08, 19 January 2024
Line 1:		Line 1:
	This page is written by Sam Chen and Abelle Jayadinata based on the materials covered in the Winter 2024 Altium PCB Workshops hosted by Evelyn Nutt. We thank Evelyn Nutt and Ethan Brinser for their expertise and knowledge, which made the writing this page possible.		If you're looking at this right now, you have probably finished the design process of your PCB and picked out all the parts/components you need. If yes, it is highly recommended to make sure you also have schematics and footprints associated with every part before moving on with reading. If not, you should refer to [[The Art of PCB Design]] page before coming back.

	If you're looking at this right now, you have probably finished the design process of your PCB and picked out all the parts/components you need. If yes, it is highly recommended to make sure you also have schematics and footprints associated with every part. If not, you should refer to The Art of PCB Design page before coming back.

	=== PCB Terminology ===		=== PCB Terminology ===
Line 11:		Line 9:
	* Symbol: the representation of an electrical component in the schematic file.		* Symbol: the representation of an electrical component in the schematic file.
	* Net: Any wire that connects to a node. In Altium, the name of the net is the combination of the index of the block (chip) and the component it connects to.		* Net: Any wire that connects to a node. In Altium, the name of the net is the combination of the index of the block (chip) and the component it connects to.
	* ~~Tags~~: Yellow-colored ~~tags~~. ~~The~~ input (inward pointing) tag ~~means “From another sheet, import this net”~~ defined by the name of the net indicated in the tag. There ~~can~~ also be output and bidirectional tags.		* Tag: Yellow-colored arrow-shaped items in the schematics file. From a separate sheet, the input (inward pointing) tag imports the net defined by the name of the net indicated in the tag. There are also output and bidirectional tags.
	* Harness: a group of nets connected to the same terminal. In GPIO/SPI/UART/I2C serial communication methods, the TX and RX data lines will often be grouped by a harness for clarity.		* Harness: a group of nets connected to the same terminal. In GPIO/SPI/UART/I2C serial communication methods, the TX and RX data lines will often be grouped by a harness for clarity.

Line 23:		Line 21:

	* Designing the schematics means you will wire up the necessary electrical components that make your PCB board function electrically. You should refer to the datasheets of different parts to see the additional components you might need.		* Designing the schematics means you will wire up the necessary electrical components that make your PCB board function electrically. You should refer to the datasheets of different parts to see the additional components you might need.
	* The Altium schematic of a completed board shows a block diagram with all the electrical components of the board. Each block represents a chip and has a detailed ~~file~~ associated with it.		* The Altium schematic sheet of a completed board shows a block diagram with all the electrical components of the board. Each block represents a chip and has a detailed sheet associated with it.
	* If you are confused about the functions of components shown in a schematic file, [https://www.khanacademy.org/science/electrical-engineering Khan Academy] can be a great resource for understanding electrical components and what they are used for.		* If you are confused about the functions of components shown in a schematic file, [https://www.khanacademy.org/science/electrical-engineering Khan Academy] can be a great resource for understanding electrical components and what they are used for.
	* When the schematic is done, Altium will generate a netlist and import it to the PCB document. You will see all the nets turned into tracks on the PCB, which size can be customized.		* When the schematic is done, Altium will generate a netlist and import it to the PCB document. You will see all the nets turned into tracks on the PCB, which size can be customized.
Line 51:		Line 49:

	After all the checks are done, a 3D model will be generated, and all the information can be sent to a fabrication company.		After all the checks are done, a 3D model will be generated, and all the information can be sent to a fabrication company.

			=== Authors' Note ===
			This page is written on January 18, 2024 by [https://ssi-teams.slack.com/team/U045V0EE46Q Sam Chen] and [https://ssi-teams.slack.com/team/U04484CR1SQ Abelle Jayadinata] based on the materials covered in the [https://docs.google.com/document/d/14Ilml3RbP6zr4GWvh4mAetntX6BX1ORxpdkTMpOlbTM/edit?usp=sharing Winter 2024 Altium PCB Workshops] hosted by [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt]. We thank [https://ssi-teams.slack.com/team/U02F79U8A11 Evelyn Nutt] and [https://ssi-teams.slack.com/team/U0602L5Q31B Ethan Brinser] for their expertise and knowledge, which made the writing of this page possible.

Samchen2: Added Schematics & Footprints sections

2024-01-19T07:03:12Z

Added Schematics & Footprints sections

@@ Line 1: / Line 1: @@
-This page is written by Sam Chen and Abelle Jayadinata based on the materials covered in the Winter 2024 Altium PCB Workshops hosted by Evelyn Nutt. All credits go to her.
+This page is written by Sam Chen and Abelle Jayadinata based on the materials covered in the Winter 2024 Altium PCB Workshops hosted by Evelyn Nutt. We thank Evelyn Nutt and Ethan Brinser for their expertise and knowledge, which made the writing this page possible.
 If you're looking at this right now, you have probably finished the design process of your PCB and picked out all the parts/components you need. If yes, it is highly recommended to make sure you also have schematics and footprints associated with every part. If not, you should refer to The Art of PCB Design page before coming back.
@@ Line 12: / Line 12: @@
 * Net: Any wire that connects to a node. In Altium, the name of the net is the combination of the index of the block (chip) and the component it connects to.
 * Tags: Yellow-colored tags. The input (inward pointing) tag means “From another sheet, import this net” defined by the name of the net indicated in the tag. There can also be output and bidirectional tags.
-* Harness: a group of wires connected to the same terminal. In GPIO/SPI/UART/I2C serial communication methods, the TX and RX data lines will often be grouped by a harness for clarity.
+* Harness: a group of nets connected to the same terminal. In GPIO/SPI/UART/I2C serial communication methods, the TX and RX data lines will often be grouped by a harness for clarity.
-==== Footprint Terminology ====
+==== Footprints Terminology ====
-* Footprint: the representation of an electrical component in the PCB file. They are also the physical traces of the components that you will see on the PCB.
+* Footprint: the representation of an electrical component in the PCB file. It also indicates the location of an electrical component, and you will see it on the manufactured PCB.
-* Via: A hole in the PCB, electrically connects through the board. The copper conductive part is inside the PCB. The purpose of this is to move the copper track to the other side of the PCB and prevent two nets from overlapping on the same side.
+* Trace: the copper wires that connect different electrical components on the PCB.

Samchen2: Added PCB Terminology section

2024-01-19T06:45:29Z

Added PCB Terminology section

New page

This page is written by Sam Chen and Abelle Jayadinata based on the materials covered in the Winter 2024 Altium PCB Workshops hosted by Evelyn Nutt. All credits go to her.

If you're looking at this right now, you have probably finished the design process of your PCB and picked out all the parts/components you need. If yes, it is highly recommended to make sure you also have schematics and footprints associated with every part. If not, you should refer to The Art of PCB Design page before coming back.

=== PCB Terminology ===

* PCB: Printed Circuit Board.

==== Schematics Terminology ====

* Symbol: the representation of an electrical component in the schematic file.
* Net: Any wire that connects to a node. In Altium, the name of the net is the combination of the index of the block (chip) and the component it connects to.
* Tags: Yellow-colored tags. The input (inward pointing) tag means “From another sheet, import this net” defined by the name of the net indicated in the tag. There can also be output and bidirectional tags.
* Harness: a group of wires connected to the same terminal. In GPIO/SPI/UART/I2C serial communication methods, the TX and RX data lines will often be grouped by a harness for clarity.

==== Footprint Terminology ====

* Footprint: the representation of an electrical component in the PCB file. They are also the physical traces of the components that you will see on the PCB.
* Via: A hole in the PCB, electrically connects through the board. The copper conductive part is inside the PCB. The purpose of this is to move the copper track to the other side of the PCB and prevent two nets from overlapping on the same side.