OpComms System IV Mechanical Design Log - Revision history

Ehillstrom: added stub in Mech. drawings

2015-12-11T20:57:44Z

added stub in Mech. drawings

← Older revision		Revision as of 20:57, 11 December 2015
Line 21:		Line 21:
	== Mechanical Drawings ==		== Mechanical Drawings ==
	What follows is a the complete set of assembly and component drawings for the system. These drawings were generated with Dassault Systèmes SolidWorks.		What follows is a the complete set of assembly and component drawings for the system. These drawings were generated with Dassault Systèmes SolidWorks.

			{{opcomms-stub}}

	== Manufacturing ==		== Manufacturing ==

Ehillstrom: Standardized punctuation

2015-12-11T20:52:44Z

Standardized punctuation

← Older revision		Revision as of 20:52, 11 December 2015
Line 12:		Line 12:
	<gallery widths=300px heights=300px>		<gallery widths=300px heights=300px>
	\|align=center		\|align=center
	File:SysIV_Initial_Design.png \| <center> Initial design concept. </center>		File:SysIV_Initial_Design.png \| <center> Initial design concept </center>
	File:SysIV_Lens_Math.png \|<center> Lens focal distance/depth calculations. </center>		File:SysIV_Lens_Math.png \|<center> Lens focal distance/depth calculations </center>
	File:SysIV_Lens_Math_Whiteboard.jpg\|<center> Secondary optic placement calculations </center>		File:SysIV_Lens_Math_Whiteboard.jpg\|<center> Secondary optic placement calculations </center>
	File:SysIV_Mounting_Bracket_Design.png \|<center> Design for mounting bracket. </center>		File:SysIV_Mounting_Bracket_Design.png \|<center> Design for mounting bracket </center>
	File:SysIV_PD_Clip_Design.jpg\|<center> Design for photodetector mounting clip </center>		File:SysIV_PD_Clip_Design.jpg\|<center> Design for photodetector mounting clip </center>
	</gallery>		</gallery>

Ehillstrom: Added images to initial design gallery

2015-12-11T20:52:17Z

Added images to initial design gallery

← Older revision		Revision as of 20:52, 11 December 2015
Line 14:		Line 14:
	File:SysIV_Initial_Design.png \| <center> Initial design concept. </center>		File:SysIV_Initial_Design.png \| <center> Initial design concept. </center>
	File:SysIV_Lens_Math.png \|<center> Lens focal distance/depth calculations. </center>		File:SysIV_Lens_Math.png \|<center> Lens focal distance/depth calculations. </center>
	File:SysIV_Mounting_Bracket_Design.png \|<center> Design of mounting bracket. </center>		File:SysIV_Lens_Math_Whiteboard.jpg\|<center> Secondary optic placement calculations </center>
			File:SysIV_Mounting_Bracket_Design.png \|<center> Design for mounting bracket. </center>
			File:SysIV_PD_Clip_Design.jpg\|<center> Design for photodetector mounting clip </center>
	</gallery>		</gallery>

Ehillstrom: Added Sections: Initial Design Concept, Mechanical Drawings, Manufucturing, and Laser Bidirectionality

2015-12-11T10:00:01Z

Added Sections: Initial Design Concept, Mechanical Drawings, Manufucturing, and Laser Bidirectionality

← Older revision		Revision as of 10:00, 11 December 2015
Line 1:		Line 1:
	~~{{opcomms~~-~~stub}}~~		This page details the mechanical design and manufacturing process for the latest revision of the [[Satellites \| Optical Communications Team]] receiver system, [[OpComms System IV\|System IV]], otherwise known as Baby Black Box. Although the first design iteration of this system is complete, some refinements may follow, with the possible addition of a laser to the receive node to enable bidirectionality in communications and alignment.

			== Initial Design Concept ==
			The design goals of this system were: (1) to decrease weight, so as to decrease strain on the motor, (2) complementarily, to decrease torque on the motor, particularly in the axis of altitude rotation, and (3) to more finely focus light into the photodetector system.

			The first two goals were addressed by purchasing a [[https://en.wikipedia.org/wiki/Fresnel_lens\| Fresnel lens]] with a slightly shorter focal length than the previous system, allowing the whole receiver to have a smaller depth, and by changing the format of the frame from a Duron (hardboard) cube to a pyramid structure composed of carbon fiber, plastic, and foamcore (although this was initially planned as plastic sheeting). The carbon fiber framing serves to provide a structural element for Baby Black Box, ensuring that the thin Fresnel lens is not under any external loads and will not deform. In addition, an effort was made to provide a mounting point calibrated to the center of mass of Baby Black Box, such that the torques were balanced about the axis of altitude rotation of the motorized mount. Due to the pyramidal shape, this resulted in a reduction of torque about the horizontal axis as well. The corner mounting points set the angle between carbon fiber rods to precisely control the focal distance of the Fresnel lens, and snap connections serve to secure the photodetector in place. The foamcore sides and lens cap protect the optics of the device and to screen out external light ([[Signal-to-noise ratio#Noise\|noise]]).

			To address the third design goal, a secondary aspherical lens was purchased. An enclosure was created to fix this lens directly to the photodetector, with the intent that the focal calibration of this lens would be much less sensitive to misalignment from transport and handling.

			The following drawings show the initial design process and supporting analysis. This is by no means constitutes a full engineering review, but demonstrates the thought process behind key design decisions.

			<gallery widths=300px heights=300px>
			\|align=center
			File:SysIV_Initial_Design.png \| <center> Initial design concept. </center>
			File:SysIV_Lens_Math.png \|<center> Lens focal distance/depth calculations. </center>
			File:SysIV_Mounting_Bracket_Design.png \|<center> Design of mounting bracket. </center>
			</gallery>

			== Mechanical Drawings ==
			What follows is a the complete set of assembly and component drawings for the system. These drawings were generated with Dassault Systèmes SolidWorks.

			== Manufacturing ==
			The connections for Baby Black Box were 3D printed in ABS plastic using a Stratasys Fused Deposition Modeling (FDM) machine. An attempt was made to orient printed parts to align the layering of the printer such that it did not follow the principle axes of stress. Tolerances were set at 0.01 inches to create firm joints where carbon fiber rod was inserted into end caps, and to ensure sound contact in snap connectors.

			The structural members were cut from 0.29" uni-axially wrapped carbon fiber rod and were cemented into their sockets once the the lengths were checked for accuracy.

			An adaptor block, used to interface with the altitude azimuth mounting system, had been previously manufactured by the team. This block has one slanted side and one straight one, which match the interior surfaces of the arms' mounting system, and two mounting holes used to bolt on a receiver system. The block was machined from Delrin plastic (a brand name for acetal resin, or [[https://en.wikipedia.org/wiki/Polyoxymethylene\| Polyoxymethylene]]), which is known for its durability and machinability. This adaptor was used with several previous OpComms systems.

			== Addition of Laser for Bidirectionality ==
			It has been proposed that the system integrate a laser mount directly into Baby Black Box. This would allow nodes to be identical and implement a symmetrical alignment and fine adjustment algorithm in the field, as well as enabling communications in both directions. If the team decides to pursue this path, design work for a bidirectional system will commence in January of 2016.


	[[Category:Optical Communications]]		[[Category:Optical Communications]]

Ehillstrom: Created page with "{{opcomms-stub}} Category:Optical Communications"

2015-12-05T21:31:43Z

Created page with "{{opcomms-stub}} Category:Optical Communications"

New page

{{opcomms-stub}}

[[Category:Optical Communications]]

← Older revision		Revision as of 20:52, 11 December 2015
Line 14:		Line 14:
	File:SysIV_Initial_Design.png \| <center> Initial design concept. </center>		File:SysIV_Initial_Design.png \| <center> Initial design concept. </center>
	File:SysIV_Lens_Math.png \|<center> Lens focal distance/depth calculations. </center>		File:SysIV_Lens_Math.png \|<center> Lens focal distance/depth calculations. </center>
	File:SysIV_Mounting_Bracket_Design.png \|<center> Design of mounting bracket. </center>		File:SysIV_Lens_Math_Whiteboard.jpg\|<center> Secondary optic placement calculations </center>
			File:SysIV_Mounting_Bracket_Design.png \|<center> Design for mounting bracket. </center>
			File:SysIV_PD_Clip_Design.jpg\|<center> Design for photodetector mounting clip </center>
	</gallery>		</gallery>