Balloons Gen 1 Radio

From Stanford SSI Wiki
Revision as of 23:21, 15 August 2017 by Ksafin (talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search
Macaw
Part of the HONEY Architecture series
& the HABEES series
Chief Designer Vinh Nguyen
Technology Line Balloons Core Radio
Version Generation I
Name Macaw
General
HONEY Standards Venom Breakout Fang Breakout Board Naming
Core Software
STINGR
Core Avionics
The Count
Core Power
Biscuit
Core Peripherals
Cobra Viper ProtoBee
Core Radio
Macaw
Test & Prototype
QueenBee
Guides
Making a HONEY Board Using STINGR Using QueenBee Making a Prototype
VE

Macaw is the first generation of a VHF/UHF transmit/receive board for Balloons Core Avionics. The purpose of the radio board is to provide an alternate means of transmitting payload vitals to the ground, in addition to RockBlock (which requires buying credits to transmit data). In addition, the radio board provides a much higher data rate than Iridium, which can be used to transmit payload vitals more often, and larger data (such as images or video).

Design

Macaw has three DORJI radios, which can be either DRA818Vs (which can transmit from 134MHz to 174MHz in the Very High Frequency(VHF) Band) or DRA818Us (which can transmit from 400-470MHz in the Ultra High Frequency (UHF) Band). Each radio also has a current sensor to monitor the amount of current being drawn from that radio. In Macaw all functionalities of the DORJI radios are supported, which means that any of the radios can be transmit or receive radios, and VHF or UHF radios, although one is designated as the APRS radio (Automatic Packet Reporting System), and the other two are designated as VHF Transmit and VHF Receive. The APRS radio is responsible for transmitting the payload vitals to the ground, while the other two are reserved for higher data-rate applications; however, in the board the hardware for each radio is identical and any VHF radio can transmit or receive any data.

Schematics

Pinout

-APRS = Radio 1; Bottom

-VHFRX = Radio 2; Middle

-VHFTX = Radio 3; Top

Serial Ports: The communication interface between the radio and the microcontroller; used to set settings (ie transmit frequency). RX here is in the frame of the Teensy (MCU RX; radio TX).

Pin APRS VHFRX VHFTX
RX 7(RX3) 9 0
TX 8 (TX3) 10 1

MIC(Microphone): The signal input to the radio transmitter.

Pin APRS VHFRX VHFTX
DAC/A14 22/A8 32

PTT (Push-To-Talk): The signal which enables or disables transmission

Pin APRS VHFRX VHFTX
6 13 25

AF_OUT (Audio Out): The output of the radio receiver.

Pin APRS VHFRX VHFTX
14/A0 17/A3 28/A17

SQ:(Squelch): Signal for setting the squelch level (threshold for suppressing noise in received signals)

Pin APRS VHFRX VHFTX
5 12 16/A2

PD/SLP (Sleep): Signal for setting the radio to low power mode

Pin APRS VHFRX VHFTX
20/A6 23/A9 15/A1

RFPWR (RF Power): Signal for setting the radio to .5W output power or 1W output power

Pin APRS VHFRX VHFTX
21/A7 19/A5 27/A16

EN (Enable): Signal for driving a FET switch to power or unpower each radio (radio is powered if this is LOW)

Pin APRS VHFRX VHFTX
2 11 18/A4

Other System Flags

LOW PWR (Flag from Main Avionics for asserting Low Power Mode)- 24

System Ready (Flag from Main Avionics for enabling startup) - A10

F3- A11

F4- A12

F5- A13

I2C

SCL - 29/A18

SDA - 30/A19

CHIRP (Serial Communication with Main Avionics). Uses the alternate pins for HWSerial 2 on the Teensy 3.2. Radio 2 Serial will be disabled during use.

RX- 26/A15 (RX2 Alt)

TX- 31/A20 (TX2 Alt)


Issues and Future Design Ideas

Number and Kind of Radios

One issue with having three VHF radios on one board is the potential for one to interfere with the others if the transmit and receive frequencies are too near one another (crosstalk). A filter between the antenna and radio could solve this, however it requires additional space and components. If interference is significant then a receiving radio would not be able to receive while another is transmitting. In effect this would be no different than having one radio operating half-duplex; components, space, and pins could be saved by removing one radio entirely; the second radio could be changed to UHF. Additional pins and board space allows for more interfacing with the main avionics and other functionality, such as data logging or image/video recording.