L1 Certification

This is not fine This article requires considerable cleanup to meet SSI wiki quality standards. Please help the SSI Wiki by correcting formatting and fixing errors in content and organization.

In order to understand high power rocketry enough to launch and successfully recover an L1 rocket, you must read, live, and understand the following information. Level 1 Certification allows flyers to fly High Power Rockets with a total installed impulse up to 640 newton-seconds.

Background Information

NASA's online Beginner's Guide To Rockets will get you started on many of the basic principles governing rocketry. If you manage to make your way through all of these, you will understand the vernacular often used in rocketry.

Safety Codes

NAR

Certification. I will only fly high power rockets or possess high power rocket motors that are within the scope of my user certification and required licensing.

Materials. I will use only lightweight materials such as paper, wood, rubber, plastic, fiberglass, or when necessary ductile metal, for the construction of my rocket.

Motors. I will use only certified, commercially made rocket motors, and will not tamper with these motors or use them for any purposes except those recommended by the manufacturer. I will not allow smoking, open flames, nor heat sources within 25 feet of these motors.

Ignition System. I will launch my rockets with an electrical launch system, and with electrical motor igniters that are installed in the motor only after my rocket is at the launch pad or in a designated prepping area. My launch system will have a safety interlock that is in series with the launch switch that is not installed until my rocket is ready for launch, and will use a launch switch that returns to the “off” position when released. The function of onboard energetics and firing circuits will be inhibited except when my rocket is in the launching position.

Misfires. If my rocket does not launch when I press the button of my electrical launch system, I will remove the launcher’s safety interlock or disconnect its battery, and will wait 60 seconds after the last launch attempt before allowing anyone to approach the rocket.

Launch Safety. I will use a 5-second countdown before launch. I will ensure that a means is available to warn participants and spectators in the event of a problem. I will ensure that no person is closer to the launch pad than allowed by the accompanying Minimum Distance Table. When arming onboard energetics and firing circuits I will ensure that no person is at the pad except safety personnel and those required for arming and disarming operations. I will check the stability of my rocket before flight and will not fly it if it cannot be determined to be stable. When conducting a simultaneous launch of more than one high power rocket I will observe the additional requirements of NFPA 1127.

Launcher. I will launch my rocket from a stable device that provides rigid guidance until the rocket has attained a speed that ensures a stable flight, and that is pointed to within 20 degrees of vertical. If the wind speed exceeds 5 miles per hour I will use a launcher length that permits the rocket to attain a safe velocity before separation from the launcher. I will use a blast deflector to prevent the motor’s exhaust from hitting the ground. I will ensure that dry grass is cleared around each launch pad in accordance with the accompanying Minimum Distance table, and will increase this distance by a factor of 1.5 and clear that area of all combustible material if the rocket motor being launched uses titanium sponge in the propellant.

Size. My rocket will not contain any combination of motors that total more than 40,960 N-sec (9208 pound-seconds) of total impulse. My rocket will not weigh more at liftoff than one-third of the certified average thrust of the high power rocket motor(s) intended to be ignited at launch.

Flight Safety. I will not launch my rocket at targets, into clouds, near airplanes, nor on trajectories that take it directly over the heads of spectators or beyond the boundaries of the launch site, and will not put any flammable or explosive payload in my rocket. I will not launch my rockets if wind speeds exceed 20 miles per hour. I will comply with Federal Aviation Administration airspace regulations when flying, and will ensure that my rocket will not exceed any applicable altitude limit in effect at that launch site.

Launch Site. I will launch my rocket outdoors, in an open area where trees, power lines, occupied buildings, and persons not involved in the launch do not present a hazard, and that is at least as large on its smallest dimension as one-half of the maximum altitude to which rockets are allowed to be flown at that site or 1500 feet, whichever is greater, or 1000 feet for rockets with a combined total impulse of less than 160 N-sec, a total liftoff weight of less than 1500 grams, and a maximum expected altitude of less than 610 meters (2000 feet).

Launcher Location. My launcher will be 1500 feet from any occupied building or from any public highway on which traffic flow exceeds 10 vehicles per hour, not including traffic flow related to the launch. It will also be no closer than the appropriate Minimum Personnel Distance from the accompanying table from any boundary of the launch site.

Recovery System. I will use a recovery system such as a parachute in my rocket so that all parts of my rocket return safely and undamaged and can be flown again, and I will use only flame-resistant or fireproof recovery system wadding in my rocket.

Recovery Safety. I will not attempt to recover my rocket from power lines, tall trees, or other dangerous places, fly it under conditions where it is likely to recover in spectator areas or outside the launch site, nor attempt to catch it as it approaches the ground.

L1 Requirements

Sources of information: TRA L1 certification info and NAR L1 certification info.

The following is a combination of the NAR and TRA requirements and rules.

You must be at least 18 years old to be certified for Level 1. Although it is good practice to already be a member of NAR and/or TRA before certifying, in practice it is not enforced. Motors must be certified and non-experimental.

Your certifier (for NAR) needs to be either two people with the level you are attempting for, or one person with the level above the one you are attempting for. They must witness the flight.

Airframe

The rocket must be built by the flyer. The rocket shall have a display on the exterior identifying the calculated center of pressure. The rocket must be of "conventional rocket design". "Odd Rockets" including flying pyramids, saucers and flying spools will not be allowed for any certification flight. The rocket may be either a kit or scratch built. Scratch built rockets may contain commercially built components.

Recovery

Standard parachute recovery is required. Non-parachute recovery methods (e.g. tumble, helicopter, gliding, etc) are not permitted for certification flights. If the rocket is using dual deployment, the first recovery event may be via a drogue-less or streamer as long as the main or second event uses a standard parachute.

Motor

The certification flight must be with a single certified H or I motor (tested total impulse between 160.01 and 640.00 n-sec).TRA does not allow staged and/or Clustered rockets for certification flights while NAR states you must use at least one HPR motor on your certification rocket. The flyer shall be observed by the certifying member or their designated representative during the assembly (if a reload or hybrid) and preparation of the motor. Single use motors are permitted.

Electronics

Electronics are not required for level 1 certification flights.

Pre-flight Inspection

The model will be subjected to a safety inspection prior to flight. The safety inspection form is on the back of the NAR High Power Certification Application. During the safety inspection the modeler will be expected to provide oral answers to technical questions related to the safety and construction of his model. The questions may include (but not limited to) identification of the model’s center of gravity and center of pressure, methods used to determine model stability, and interpretation of the rocket motor’s designation. The certification team will initial (or check) the blocks indicating that model safety, motor certification, and the existence of a FAA waiver (if required) in effect were verified prior to flight.

Certification Flight

Level 1 Certification flight may take place at any insured launch. The certifying member (i.e. Prefect, TRA Director, NAR certifiers or TAP Member) must be present and witness the certification flight. The certifying member must witness the rocket ascend in a stable manner and descend in stabilized manner controlled by the recovery system.

Post-Flight Inspection

The rocket must be presented to the certifying member for inspection. If the rocket cannot be recovered, but can be inspected in place (power lines, tree, etc...) this is acceptable. The certifying member shall inspect the rocket for excessive damage. Excessive damage shall be considered damage to the point that if the flyer were handed another motor, the rocket could not be put on the pad and flown again safely. Damage caused by wind dragging will not cause a disqualification. If successful, the certifiers will sign the correct sheet to indicate that the certification attempt was successfully completed.

== Post-Post-Flight The certification sheets are returned to NAR or TRA Headquarters. No fees are required. The certification sheet must be returned by the certified individual or the event sponsors to NAR or TRA Headquarters to allow updating the NAR or TRA database. NAR sends an updated membership card showing the certification level upon receipt of the certification paperwork.

Non-certification

Any of the following will result in non-certification for a certification flight:

• Motor Cato
• Excessive Damage
• No recovery system deployment or tangled recovery system deployment
• Rocket drifting outside the specified launch range
• Components coming down not attached to the recovery system.
• Any other violation of TRA safety code associated with this particular flight.
• Any other legitimate reason the certifying member deems merits non-certification

Launch Locations

Map

Time launch begins

etc

Launch Day Procedures

Who You Will Meet

RSO

Mike

Cliff

Stu

What You Need To Bring

People Fuel - water food money etc

Car Fuel - petrol

Appropriate Clothing

Vendors

BAR

Range Layout

Big, cars on the side, site in the middle

Packing Your Parachute

It should not be too tight. Etc.

Here is a video.

Here is how a NAR member does it. (Cliff)

Look at these great diagrams.

Prepping Your Motor

If using a single use motor or Disposable Motor System, make sure to check that the delay on the ejection charge is correct using a simulation software (i.e. OpenRocket). If needed adjust the length of the delay grain. Then place the correct quantity of ejection propellant in the correct location. Cap it.

Here is a great video to watch.

Range Safety Check

Is your paperwork in order?

Motors

Is the motor certified, what is the motor type and average thrust? Is the delay time is approximate for rocket?

Will the rocket penetrate cloud cover?

Does your rocket motor have the ejection charge installed?

Is sufficient wadding/Kevlar installed?

What kind of motor retention system is installed?

What prevents the motor from flying-through the rocket?

Rocket Construction

Stability? Is the CG in front of the CP? Be able to identify both.

Is the nose cone fitted correctly?

Launch lugs and/or rail guides properly installed, positioned, and aligned?

Fins atttached securely and in a manner that will not cause an unsafe flight?

Is an appropriately-sized recovery system installed and attached?

Are there vent holes?

Launch Pad Procedure

The rocket should slide freely on the rail. The pad angle should be within 20 degrees of the vertical axis (normal to the surface of the earth). Flight critical electronics (if there are any) should be armed before putting in igniters. Any radio control equipment should also be nominally operating before arming the igniters.

How to install an igniter

Place in the nozzle of rocket, and tape the igniter to the rocket so it does not slide out. Make sure not to short the leads of the igniters.

Here is a great video to watch.

Success and Failure

Following the launch, the rocket will be inspected; should the airframe be deemed suitable for flight given a new motor, it will have passed L1 certification. Failed deployment, motor cato, drifting beyond a particular range (see launch officer), or the violation of other safety codes will result in a failure. L1 certification, however, is an excellent introduction to the basic operations of rockets and recovery! See Pegasus for a description of an L1 rocket used as a testbed for an L3 concept.

Final Steps

Mailing It In

You must mail in your certification form to have the rocketry association acknowledge your achievement. These are the addresses of NAR and TRA.