HONEY Standardized Connectors
| HONEY Standards | |
|---|---|
| Part of the HONEY Architecture series & the HABEES series | |
| |
| General | |
| HONEY Standards • Venom Breakout • Fang Breakout • Board Naming | |
| Core Software | |
| STINGR | |
| Core Avionics | |
| The Count | |
| Core Power | |
| Biscuit | |
| Core Peripherals | |
| Cobra • Viper • ProtoBee | |
| Core Radio | |
| Macaw | |
| Test & Prototype | |
| QueenBee | |
| Guides | |
| Making a HONEY Board • Using STINGR • Using QueenBee • Making a Prototype | |
| V • E |
This page lists all of the connectors used on various boards, as well as standardized HONEY connectors and their use cases. HONEY uses primarily (and almost exclusively) Samtec connectors -- and only uses other connectors when no available Samtec connector fills the use case.
General Layouts
The following section indicate connectors used for general things -- like sockets for teensies, the actual HONEY flight stack, and HONEY standardized breakouts.
Teensy 3.2 Socket + Mating Pins
The below are used for all HONEY Teensy 3.2 sockets -- this includes the socket itself, on the PCB side, and the male pins that are soldered to the teensy for mating with the socket. This is broken into four portions -- the internal 2x7 row of pins that are SMD on the bottom of the teensy (herein referred to as "internal row"), the two 14-pin side rows, the back 5-pin row, and the remaining 3 side pins (A10/A11/AREF). The below is broken into the socket connectors, and the male teensy-side connectors.
Sockets (PCB Side)
Internal Row (1) -- SLW-107-01-G-D
Side Rows (2) -- SLW-114-01-G-S
Back Row (1) -- SLW-105-01-G-S
A10/A11/AREF Row (1) -- SLW-103-01-G-S
Headers (Teensy Side)
Internal Row (1) -- TSM-107-04-T-DV
Side Rows (2) -- TSW-114-06-G-S
Back Row (1) -- TSW-105-06-G-S
A10/A11/AREF Row (1) -- TSW-103-06-G-S
Teensy 3.6 Socket + Mating Pins
The below are used for all HONEY Teensy 3.6 sockets -- this includes the socket itself, on the PCB side, and the male pins that are soldered to the teensy for mating with the socket. This is broken into five portions -- three sets of internal rows, that are SMD on the bottom of the Teensy; the furthest back one is referred to as Internal Row 1, the middle one is Internal Row 2, and the furthest up is Internal Row 3. Additionally, there are the two side rows, and the remaining A10/A11/AREF row. The below is broken into the socket connectors, and the male teensy-side connectors.
Sockets (PCB Side)
Internal Row 1 (1) -- SLW-105-01-G-D
Internal Row 2 (2) -- SLW-103-01-G-D
Internal Row 3 (1) -- SLW-104-01-G-D
Side Rows (2) -- SLW-124-01-G-S
A10/A11/AREF Row (1) -- SLW-103-01-G-S
Headers (Teensy Side)
Internal Row 1 (1) -- TSM-105-04-T-DV
Internal Row 2 (2) -- TSM-103-04-T-DV
Internal Row 3 (1) -- TSM-104-04-T-DV
Side Rows (2) -- TSW-124-06-G-S
A10/A11/AREF Row (1) -- TSW-103-06-G-S
HONEY Stack Connectors
Databus (stackthrough) (1) -- PTHF-130-02-G-Q-368
Databus (non-stackthrough (?) -- PTHF-130-03-G-Q-368
Powerbus (stackthrough) (1) -- ESQ-105-39-G-D-LL
CANbus (stackthrough) (1) -- ESQ-103-39-G-D-LL
Terminator Holder (1) -- TSW-104-07-G-D
Shunt (2) -- SNT-100-BK-T
HONEY Breakouts
Venom Breakout
The Venom Breakout is the HONEY-standard 50-pin 1.27mm pitch connector/cabling that provides primary data & power connections over cabling between HONEY stacks. The Venom breakout is the primary breakout used to connect payloads to the primary flight stack, as well as connect the primary flight stack to auxiliary flight stacks.
Connector: SHF-125-01-L-D-RA
Cabling: FFSD-25-D-XX.XX-01-N
where XX.XX is the length of the desired cable, in inches.
Fang Breakout
The Fang breakout is a slightly larger, 56-pin, 2.54mm pitch connector currently not heavily used, but also breaks out the 2nd CAN bus and left-over avionics pins.
Connector: TST-156-01-F-D-RA
Cabling: HCSD-28-D-XX.XX-01-S-N
where XX.XX is the length of the desired cable, in inches.
Board Connectors
The below section lists the connectors for various boards, so that they may be purchased if needed to populate a new board, or replace the connector on an old board -- or for the sake of reuse on a new board.
Viper
Venom Breakout Connector (2) -- SHF-125-01-L-D-RA
Fang Breakout Connector (1) -- TST-156-01-F-D-RA
Cobra
Stack Right Angle Pinout (1) -- TLW-114-01-G-D-RA
Teensy Right Angle Pinout (1) -- TLW-120-01-G-D-RA
ProtoBoard Sockets (4) -- SS-102-G-2
ProtoBoard Pins (4) -- BBS-102-G-A
2X4 Power Select Headers (2) -- TSW-104-07-G-D
Power Shunts (2) -- SNT-100-BK-T
Teensy 3.2 Socket (1) -- see general section above.
ProtoBee
Venom Breakout (2) -- SHF-125-01-L-D-RA
Stack Socket (1) -- SSW-119-01-G-D
Teensy Pinout Socket (1) -- SSW-119-01-G-D
Power Bus Socket (1) -- SSW-105-01-G-D
Shunts (3) -- SNT-100-BK-T
Power Rail Selector Headers -- TSW-106-07-G-S
CAN Terminator Headers -- TSW-102-07-G-S
Teensy 3.2 Socket (1) -- see general section above.
QueenBee
Teensy Pinout Socket (1) -- SSW-125-01-G-D
DataBus Socket (1) -- SSW-130-01-G-D
PowerBus Socket (1) -- SSW-112-01-G-D
Debug Socket (1) -- SSW-112-01-G-D
Venom Breakout (1) -- SHF-125-01-L-D-RA
Auxiliary Breakout (3) -- TST-104-04-G-D-LA
CAN1 Terminating Headers (1) -- TSW-102-07-G-D
CAN1/2 Terminating Headers (1) -- TSW-104-07-G-D
Shunts (3) -- SNT-100-BK-T
Teensy 3.2 Socket (1) -- see general section above.
Teensy 3.6 Socket (1) -- see general section above.