SSI-19

SSI-19
Launch date	May 16th 2015, 6:32 PM PDT
Launch site	Laird Park, Modesto, CA
Launch coordinates	37.56158, -121.14993
Flight duration	15 hrs, 11 minutes
Landing coordinates	37°50.87' N 119°5.28' W
←SSI-18 SSI Balloon Launches SSI-20→

SSI-19 was the 19th launch of SSI Balloons. SSI-19 flew for just over 15 hours and to an altitude of 119,932 ft - breaking SSI's altitude record. The launch was a demonstration of the physical feedback found at high altitude with a precision filled latex balloon. The payload maintained an altitude of approximately 118,000 feet merely by passive feedback and no active control - it was degraded by UV radiation and descended shortly after sunrise. SSI-19 landed in Yosemite just east of Grant Lake after a flight of 15 hours.

Flight Profile

SSI-19 was based on a flight method that was first successfully flown by the California Near Space Project (CNSP). The principle of the launch is inflating a large latex balloon (In the case of SSI-19, a 1600g) to a very low lift capacity (365g payload, ~140g free lift) to launch a very light payload. By barely filling the balloon and providing a very light payload, the balloon is able to ascend to a very high altitude (110,000-120,000 ft) where there is a positive feedback loop, allowing the balloon to equilibrate due to natural phenomena (no active control mechanism).

Payload Specifications

SSI-19 Payload

The SSI-19 payload was, as needed, a very barebones set of electronics. It included an APRS BigRedBee transmitter using the callsign of balloons team member Iskender Kushan (KK6MIR), a GPS for position reporting, a sizable lithium-ion battery, and a heater made of nickel-chromium (nichrome) wire. In total, the payload had a mass of about 365g. It was the first balloon to be launched during the launch of SSI-19, SSI-20, and SSI-21. CNSP graciously brought their mass-flow meter to fill the SSI-19 latex balloon to a precise lift capacity (a mission-critical aspect of this launch).

Launch site

The launch was conducted at Laird Park, just west of Modesto, CA, a site frequented by the balloons team. The team left campus at 10 am, arriving just after 11:30 am. The payload was essentially flight-ready, requiring only minor pre-flight additions and verification of system fidelity. The APRS transmitter was verified for flight-readiness by ensuring transmission on the ground, the payload was sealed, and just prior to launch, the heater was hard-wired to the battery pack (for constant heating).

Filling of the 1600g Hwoyee balloon began at around 5:30 pm. Filling was coordinated in conjunction with CNSP personnel, who used their mass-flow meter to fill the balloon with the appropriate volume of Helium as calculated and verified by SSI members. Filling was challenging due to higher than expected ground wind speeds. After filling, launching was additionally challenging due to powerful east-bound winds, which pushed the balloon nearly into the ground on multiple occasions. During a moment of south-bound winds, the balloon was released from the north end of Laird Park (in order to clear the southern tree line) and ascended at a nominal velocity.

Winds during Filling

The Flight

The storm

As expected, the balloon had a fairly slow ascent velocity due to its low free lift. It ascended at an average velocity of around 1.5 m/s, initially with a southbound heading until hitting north-bound winds 10 minutes into flight. Following ascent to approximately 10,000 feet at 7:07 PM PDT, SSI-19 had a East-Northeast heading for the majority of its flight. It reached critical altitude at around 8:00 AM PDT on May 17th, just south of Mono Lake in the Yosemite National Park. As the sun rose, the balloon began being degraded by UV radiation.

The balloon reached a peak altitude of 119,932 ft at 9:15 AM PDT, May 17th, breaking the former SSI altitude records for latex balloons. It burst shortly after this position report, indicating a descent of nearly 1,000 feet. Unequipped with a parachute, SSI-19 descended from altitude in a matter of approximately 30 minutes. It landed just east of Grant Lake, a few hundred feet off the California 395.

SSI-19 Flight Path

Debriefing

The ability of the balloon to maintain altitude on its own through almost the entire flight to such precision was a testament to the resilience of the technology. Nevertheless, problems were encountered, including the following:

• The power draw for heating was quite high; the battery started at a voltage of ~ 4.34 V and was around ~ 3.40 V upon landing. 3.20 V is the point at which the flight control system ceases to function; thus, for longer flights, more power is needed. Proposed improvements included more battery storage and, more importantly, solar panels for power regeneration.

• This flight offered an indication of how far the preloaded quantity of ballast was able to take the balloon. Granted, the turbulence experienced over Idaho resulted in considerable usage of ballast, but the fact that this occurred suggested that significantly more ballast would be required for longer journeys.

• Gas venting can also be amended; a 3-inch neck was used to allow for high volumes of gas to be vented, but this could have been reduced to a neck diameter as small as 1 inch and compensated for with a larger vent time. Venting for 5 seconds at a time with a 3 inch neck caused unnecessarily large volumes of gas to be vented.

• Better payload insulation is needed. SSI-18 used a payload wrapped in AeroGel Cryogel blanket, which was so insulative that its heaters did not need to turn on for over 10 hours. A shrinking budget and smaller timeframe did not permit the team to put Aerogel on this flight, but its potential value to future payload containers was demonstrated.

Milestones

• First international launch of SSI Balloons
• Longest flight of SSI Balloons (as of September 2015)
• Longest ground distance traveled by any SSI Balloons mission (as of September 2015)

Gallery

• 

  Ground path
• 

  Altitude data