Difference between revisions of "Project UV"
| Line 10: | Line 10: | ||
== SSI-28 == | == SSI-28 == | ||
[[File:SSI_28_09.png | left | thumb| <center> SSI-28 data</center>]] | [[File:SSI_28_09.png | left | thumb| <center> SSI-28 data</center>]] | ||
| − | [[File:SSI_UV_01.png | left | thumb| <center> SSI-28 data</center>]] | + | [[File:SSI_UV_01.png | left | thumb| <center> Averaged SSI-28 data</center>]] |
[[File:SSI_28_10.png | left | thumb| <center> SSI-28 data</center>]] | [[File:SSI_28_10.png | left | thumb| <center> SSI-28 data</center>]] | ||
| − | [[File:SSI_UV_02.png | left | thumb| <center> SSI-28 data</center>]] | + | [[File:SSI_UV_02.png | left | thumb| <center> Averaged SSI-28 data</center>]] |
In order to collect data on the levels of ultra violet A and B present at different altitudes, a sensor for each UV type was launched on [[SSI-28]]. From the data, it can be concluded that there is much more UV A than UV B, and it does in fact increase with altitude, reaching a max value of 1323 microwatts/cm^2 for UV A and 292 microwatts/cm^2 for UV B. In addition, there is a lot of noise in the values, with a corresponding oscillation of values, which is due to the sensor being on one side, and the payload spinning during its flight. Thus, the value where the sun is directly facing the latex would correspond to the high part of the wave. | In order to collect data on the levels of ultra violet A and B present at different altitudes, a sensor for each UV type was launched on [[SSI-28]]. From the data, it can be concluded that there is much more UV A than UV B, and it does in fact increase with altitude, reaching a max value of 1323 microwatts/cm^2 for UV A and 292 microwatts/cm^2 for UV B. In addition, there is a lot of noise in the values, with a corresponding oscillation of values, which is due to the sensor being on one side, and the payload spinning during its flight. Thus, the value where the sun is directly facing the latex would correspond to the high part of the wave. | ||
| Line 22: | Line 22: | ||
File:SSI_28_09.png | <center> Project UV data</center> | File:SSI_28_09.png | <center> Project UV data</center> | ||
File:SSI_28_10.png | <center> Project UV data</center> | File:SSI_28_10.png | <center> Project UV data</center> | ||
| + | File:SSI_UV_01.png | <center> Project UV data</center> | ||
| + | File:SSI_UV_02.png | <center> Project UV data</center> | ||
</gallery> | </gallery> | ||
{{balloon-footer}} | {{balloon-footer}} | ||
[[Category: High Altitude Balloons]][[Category: Projects]] | [[Category: High Altitude Balloons]][[Category: Projects]] | ||
Revision as of 08:20, 1 February 2016
Project UV is the 2015-2016 Balloons team project to develop effective countermeasures against the UV degradation of latex balloons, in order to increase the potential flight time of future payloads.
The current team leads are Davy Ragland and Yuji Sugimoto.
Chemical protection
Because ultra violet radiation physically degrades the polymers within the latex, a chemical solution may elongate its lifespan. A preliminary test was done with a set of various chemical coatings, balloon types, and strech values. However, the test had to be stopped for winter break, so the degradation point of some samples could only be predicted, not verified. Nevertheless, the initial results seem optimistic.
SSI-28
In order to collect data on the levels of ultra violet A and B present at different altitudes, a sensor for each UV type was launched on SSI-28. From the data, it can be concluded that there is much more UV A than UV B, and it does in fact increase with altitude, reaching a max value of 1323 microwatts/cm^2 for UV A and 292 microwatts/cm^2 for UV B. In addition, there is a lot of noise in the values, with a corresponding oscillation of values, which is due to the sensor being on one side, and the payload spinning during its flight. Thus, the value where the sun is directly facing the latex would correspond to the high part of the wave.
Chemical concentration
As result of the positive results of the chemical protection tests, a new experiment will be done indoors with UV LEDs that emit light at 365 manometers. This will be to control for and calculate the exact amount of UV that the latex is being exposed to. The UC sensors will be used to determine the proportion of UV concentration to natural sunlight at the desired altitude. The independent variable will be the concentration of chemical spray per area, in order determine the ideal amount to apply onto the balloon.
Gallery
Project UV data 
Project UV data 
Project UV data 
Project UV data 
Project UV data
| Balloon Launches | |
|---|---|
| 2014-15 | SSI-19 • 20 • 21 • 22 |
| 2015-16 | SSI-23(a) • 24 • 25 • 26 • 27 • 28 • 29 • 30 • 31 • 32 • 33 • 34 • 35 • 36 • 37 • 38 • 39 • 40 • 41 • 42 • 43 |
| 2016-17 | 44 • 45 • 46 • 47 • 48 • 49 • 50 • 51 • 52 |
| 2017-18 | |
| 2018-19 | 83 • 86 • 87 • 90 • 91 |
| 2019-20 | 92 • 93 • 97 |
| V • E | |